This is the COMPLETE official full service repair manual for the CNH NEF F4CE, NEF F4DE, NEF F4GE, NEF F4HE ENGINES 4 CYLINDERS TIER 3. Professional work shop technicians use and trust this service manuals - now you can too!

In book CNH NEF F4CE, NEF F4DE, NEF F4GE, NEF F4HE ENGINES 4 CYLINDERS TIER 3 SERVICE REPAIR MANUAL you will find the complete informations was keeped like the original manufacturer book. Also, you will find also datasheet information about circuits, diagrams, equipments.

For CNH NEF F4CE, NEF F4DE, NEF F4GE, NEF F4HE ENGINES 4 CYLINDERS TIER 3, the following contents are usually covered:
ENGINES CNH NEF F4CE - F4DE - F4GE - F4HE

4 Cylinders, Mechanical and Electronic Drive Common Rail
Tier 3

ENGINES FAMILY:
F4CE9484 - F4DE9484 - F4GE9484 - F4HE9484


Introduction
General specifications 1
Fuel 2
Duty - Industrial application 3
Overhaul and technical specifications 4
Tools 5
Engine technical cards

SECTION 1
General Specifications

NOMENCLATURE (Coding of the engines of origin)
LUBRICATION
OIL VAPOUR RECIRCULATING SYSTEM
COOLING SYSTEM
AIR INDUCTION BOOST DIAGRAM
- Boosting version engines
- Description
- Inter-cooled engine version
- Description
EXHAUST GAS RE-CIRCULATION SYSTEM (EGR)

SECTION 2
Fuel
4-CYLINDER ENGINES WITH BOSCH ROTARY
MECHANICAL PUMP
- General information
- Description of working principles
FEED PUMP
- Example of identification
CP3 HIGH PRESSURE PUMP
- High pressure pump-inside structure
- Working principle
- Operation
RAIL
RELIEF VALVE
PRIMING PUMP
FUEL FILTER
HIGH PRESSURE ELECTRONIC INJECTION SYSTEM (COMMON RAIL)
EDC 7 OPERATION
WORKING PROCESS
FUEL SYSTEM LAYOUT

SECTION 3
Engine
GENERAL INFORMATION
PART ONE - MECHANICAL COMPONENTS
OVERHAUL OF THE 4 CYLINDER ENGINE PROVIDED WITH MECHANICAL ROTARY PUMP
Preface
- Engine setting operations for the assembly on turning stand
- Disassembly of application components
- Installation of rear components
- Installation of rear components with reduced distribution
- Flywheel installation
- Installation of front components
- Assembly of additional masses
- Timing of additional masses
- Completion of engine re-assembly
- Rotary feed pump disassembly and assembly procedure
- Feed system bleed procedure
- Power take-off disassembly and assembly procedure
- Checks and controls

PART ONE - MECHANIC OVERHAUL OF ENGINES WITH ELECTRONIC CONTROL (COMMON RAIL)
RAIL
RELIEF VALVE
ELECTRO-INJECTOR
PRESSURE LIMITER FOR FUEL RETURN
GENERAL SPECIFICATIONS
- Section pictures of complete engine - common rail version
- Engine setting operations for the assembly on turning stand
ENGINE OVERHAUL
- Preface
- Disassembly of application components
- Assembly of application components
- Completion of the engine

PART TWO - ELECTRICAL EQUIPMENT - MECHANICALS
ENGINES
ELECTRICAL COMPONENT LAYOUT (4 CYL. ENGINES WITH ROTARY PUMP)
- Cooling liquid temperature sensor
- Starter
- KSB Water temperature sensor
- Electromagnets assembled to feed pump
- Oil pressure switch
- Alternator
- Pre-post heating resistor

PART TWO - ELECTRICAL EQUIPMENT - ELECTRONICS
ENGINES
LOCATION OF MAIN ELECTRICAL COMPONENTS
- EDC7 ECU
- Connector to injectors (A)
- Feed connector (B) to components and to functions of the specific equipment
- Connector to sensors (C)
- Temperature and air-pressure sensor
- Sensor of engines oil temperature and pressure
- Driving shaft sensor
- Timing system sensor
- Fuel pressure sensor
- Fuel temperature sensor
- Resistor pre-post heating
- Cooling liquid temperature sensor
- Starter
- Electro-injectors

PART THREE - TROUBLESHOOTING (MECHANICALS ENGINES)
PART THREE - TROUBLESHOOTING (ELECTRONICS ENGINES)
METHODS OF DIAGNOSIS
FAULT CODES

PART FOUR - MAINTENANCE PLANNING
MAINTENANCE PLANNING
- Recovery
- Planning of controls and periodical intervention
- Checks not included in maintenance planning-daily checks
MAINTENANCE PROCEDURES
- Checks and controls
- Engine oil level check
- Check of fuel system
- Cooling system check
- Lubricating system check
- Check of water presence within fuel filter or pre-filter
- Check of drive belt tensioning
- Check of belts tear and wear status
- Check and setting of tappet clearance
- Oil motor and filter replacement
- Fuel filter replacement
- Alternator belt replacement


This manual includes complete solutions for repairing your machine step by step, whether you have experience in this field or not. However, we often recommend that you use a mechanic to solve your problems.


The manual covers:

* Detailed substeps expand on repair procedure information
* Notes, cautions and warnings throughout each chapter pinpoint critical information.
* Numbered instructions guide you through every repair procedure step by step.
* Bold figure number help you quickly match illustrations with instructions.
* Detailed illustrations, drawings and photos guide you through every procedure.
* Enlarged inset helps you identify and examine parts in detail.
* Numbered table of contents easy to use so that you can find the information you need fast.
* This CNH NEF F4CE, NEF F4DE, NEF F4GE, NEF F4HE ENGINES 4 CYLINDERS TIER 3 service manual also makes it easy to diagnose and repair problems with your machines electrical system. Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use.

This manual is the official full COMPLETE factory service repair manual for the CNH NEF F4CE, NEF F4DE, NEF F4GE, NEF F4HE ENGINES 4 CYLINDERS TIER 3 SERVICE REPAIR MANUAL.

Our main priority is gaining respect for each client and 100 satisfaction. We want to have happy customers for their purchases and loyalty to, and we hope to receive recommendations to other potential customers.

DOWNLOAD IT NOW CNH NEF F4CE, NEF F4DE, NEF F4GE, NEF F4HE ENGINES 4 CYLINDERS TIER 3 SERVICE MANUAL!!

PRODUCT DETAILS:
----------------------------------------------
File Format: PDF
Language: English
Printable: without any restriction
Delivery: Download link will appear on the checkout page after payment is complete.
Requirements: Adobe PDF Reader